Intel centrino wireless n 1000 5ghz software#
Intel centrino wireless n 1000 5ghz Bluetooth#
Intel centrino wireless n 1000 5ghz series#

I am not sure if you want to mark this thread as as your end result is certainly not solving the original problem of you thinking the card was not using wireless-N. In any case, I am glad you got your wifi a bit more stable FathisAeril. With wd_disable, 0 is the system default, 1 is off and 2 is on, while the default setting is 0.

Intel centrino wireless n 1000 5ghz Bluetooth#

Since the bt_coex_active parameter is simply whether or not the bluetooth is enabled on a card that has both, and the wd_disable=2 simply forces on the watchdog, which should already be on per the system defaults. The second modprobe.d example, I am really not sure what is hoped to be achieved by the second two parameters either. So if your HW advertises 150Mb/s the theoretical maximum is going to be just under 18MB/s. The lower case 'b' means bits, while an upper-case 'B' represents bytes. Seeing that a byte is made up of 8 bits, the 'around 6mb/s' is correct if you assume that FathisAeril really meant 'around 6MB/s' or six megabytes per second. Disabling N (11n_disable=1) will result in wireless-G which is 54Mb/s. Just for clairty's sake, I just want to point out that there still appears to be some confusion about Mb vs MB.

Last edited by manuelschneid3r ( 16:04:59) Parm: amsdu_size_8K:enable 8K amsdu size (default 0) (int) sys/module/iwlwifi/parameters$ modinfo iwlwifi | grep parm | while read X do echo $X Y=$ cat $Z done Parm: 5ghz_disable:disable 5GHz band (default: 0 ) (bool) Parm: auto_agg:enable agg w/o check traffic load (default: enable) (bool) Parm: power_level:default power save level (range from 1 - 5, default: 1) (int) Parm: power_save:enable WiFi power management (default: disable) (bool) Parm: led_mode:0=system default, 1=On(RF On)/Off(RF Off), 2=blinking, 3=Off (default: 0) (int) Parm: bt_coex_active:enable wifi/bt co-exist (default: enable) (bool) Parm: wd_disable:Disable stuck queue watchdog timer 0=system default, 1=disable, 2=enable (default: 0) (int) Parm: plcp_check:Check plcp health (default: 1 ) (bool) Parm: bt_ch_inhibition:Enable BT channel inhibition (default: enable) (bool) Parm: antenna_coupling:specify antenna coupling in dB (defualt: 0 dB) (int) Parm: fw_restart:restart firmware in case of error (int) Parm: amsdu_size_8K:enable 8K amsdu size (int) Parm: 11n_disable:disable 11n functionality, bitmap: 1: full, 2: agg TX, 4: agg RX (uint)

Intel centrino wireless n 1000 5ghz software#

Parm: swcrypto:using crypto in software (default 0 ) (int)

Intel centrino wireless n 1000 5ghz series#

00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)Ġ0:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)Ġ0:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)Ġ0:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05)Ġ0:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)Ġ0:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5)Ġ0:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5)Ġ0:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5)Ġ0:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05)Ġ0:1f.0 ISA bridge: Intel Corporation QS67 Express Chipset Family LPC Controller (rev 05)Ġ0:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05)Ġ0:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)Ġ2:00.0 Network controller: Intel Corporation Centrino Advanced-N 6230 (rev 34)Ġ3:00.0 USB controller: Fresco Logic FL1009 USB 3.0 Host Controller (rev ~]$ modinfo iwlwifi | grep parm